ScopeMaterial & ManufactureHeat Treatment RequirementsChemical RequirementsImpact RequirementsMechanical TestingLengthsRequired Markings on Each LengthReferenced DocumentsOrder InformationASTM A333 covers nominal (average) wall seamless and welded carbon and alloy steel pipe intended for use at low temperatures. Several grades of ferritic steel are included. Some product sizes may not be available under this specification because heavier wall thicknesses have an adverse affect on low-temperature impact properties.Looking for specific post-production services? See our full list.ASTM S/A 333 Low Temperature Pipe A333 Low Temp Steel ASTM A333 (ASME S/A-333) Pipe grades permit low temperature service. This specification covers nominal (average) walled pipe almost exclusively in seamless.
ASME SA 333 Grade 6 Carbon Steel Seamless Pipes FerropipePipes and Tubes manufactured as per ASME SA 333 Grade 6 are certified with En 10204 Type 3.1/3.2. IBR,NACE,HIC,IGC,IMPACT are adhered as supplementary testing requirements. A For intermediate temperatures, the holding time shall be determined by straight-line interpolation.
ScopeMaterial & ManufactureHeat Treatment RequirementsChemical RequirementsImpact RequirementsMechanical TestingLengthsRequired Markings on Each LengthReferenced DocumentsOrder InformationASTM A333 covers nominal (average) wall seamless and welded carbon and alloy steel pipe intended for use at low temperatures. Several grades of ferritic steel are included. Some product sizes may not be available under this specification because heavier wall thicknesses have an adverse affect on low-temperature impact properties.ASTM A333 Grade 6 seamless pipe, ASTM A333 Grade 6 ASTM A333 Grade 6 seamless pipes are applicated for low temperature service. ASTM A333 Grade 6 Seamless Pipe involved is similar to AISI 4032 low alloy steel. ASTM A333 Grade 6 is the part of standard covers wall seamless and welded carbon and alloy
ASTM A333/SA333 Pipe (For Low Temperature Services ASTM A333 Grade 6 pipe is the common grades refer to the low temperature applications. Enpro supply ASTM A333 pipe with below conditions:Standard:ASTM A333/ A333M Grade:Grade 1, Grade 3, Grade 4, Grade 6, Grade 7, Grade 7, Grade 8, Grade 9, Grade 10 and Grade 11 OD:NPS 1/8 inch to NPS 20 inch, 10.13mm to 1219mm
*A Charpy V-Notch Impact Value Required for Acceptance (Average of Three Specimens). *B Minimum Charpy V-Notch Impact Value Without Requiring Retest (One Specimen Only of a Set). *The impact test temperature shall be -50°F[-45°C] for ASTM A420 Gr. WPL6. 4. Maximum Allowable Stress at Elevated Temperatures
ASTM A420 WPL6 for Low Temperature Pipe Fittings- Besides Grade WPL6, the standard also includes WPL9, WPL3, WPL8, impact test temperature correspondingly at -45, -75, -100, -195. ASTM A420 covers elbow, tee, reducer, cap, union and etc, which manufactured according to ASME B16.9, ASME B16.11, MSS SP-79 and MSS SP-95, types in seamless and welded structual pipe fittings.
Difference between ASTM A106 & A333Oct 12, 2004 · I believe A333 is a good substitute for A106-B for a broad range of temeperatures Based on my review of ASME B31.3 (Table A-1) the allowable stress for A106 Grade b is 16ksi to 500F; for A333 grade 6 - 20Ksi to 400F and 18.9ksi to 500F It would be fair to say that, given the application has an operating temperature greater than -20F, either
A333 Gr6 has proven impact toughness at -50F (-45C), and is commonly used in applications where the piping is exposed directly to cold environments during construction and/or in operation. A333 Gr6 is also commonly used for pressure piping of compressed gas, where a crack would be expected to have catastrophic consequences.
Theoretical A333-6 vs A106B question. - ASME (mechanical Jul 11, 2005 · metengr (Materials) 11 Jul 05 10:29. Yes, A-333 Grade 6 should easily meet 15 ft-lbs at -50 deg F. As far as A-106, this steel would probably be too close to call at -50 deg F (if I were a betting man, I would say it would not generally meet 15 ft-lbs at -50 deg F). RE:Theoretical A333-6 ASTM A333 Gr.1, Gr.6, Gr.8 Seamless Low-Temperature Impact Temperature Grade Minimum Impact Test Temperature °F °C 1 50 45 6 50 45 8 320 195 Impact Temperature Reduction Specimen Width Along Notch or Actual Material Thickness Temperature Reduction, Degrees Colder A in. mm °F °C 0.394