Ni-15.5Cr-8Fe alloy:Ni-15.5Cr-2.5Ti-0.7Al-1Nb-7Fe alloy:Ni-15Cr-28Co-Mo-Ti-Al alloy:Ni-19Cr-18Co-4Mo-3Ti-3Al-B alloy:Ni-19Cr-18Fe-3Mo-5Nb-Ti-Al alloy
Data Sheets:Series 900 Safety Relief Valves, Kunkle Valve 4. 1030 psig (71 barg) for steam service with standard stainless steel spring. 5. 900 psig (62 barg) for liquid service, or with high-temperature alloy steel spring. 6. 600 psig (41.4 barg) for liquid service, or with high-temperature alloy steel spring. 7. Subject to pressure and
EN 10152 DC06 +ZE 0,02 0,25 0,020 0,020 0,03 0,01 0,30 EN 10152 DC05 +ZE 0,06 0,35 0,025 0,025 0,03 0,01 - surface textures as set out in the Data Sheets:Electro-galvanised Steel Sheet (file reference EG 1) and Cold Rolled Products (file reference B1). For further information, contact:
Online Materials Information Resource - MatWebMaterial property database with data sheets of thermoplastic and thermoset polymers such as nylon, polycarbonate, polyethylene; metal alloys, aluminum, steel, titanium, nickel, cobalt, and zinc alloys; ceramics, lubricants. Free search tools include mechanical property searches. Comparison and exports to Finite Element Analysis FEA software SolidWorks, ANSYS, ALGOR, and more.
S355JR - OvakoThe data and examples are only general recommendations and not a warranty or a guarantee. The suitability of a product for a specific application can be confirmed only by Ovako once given the actual conditions.The purchaser of an Ovako product has the responsibility to ascertain and control the applicability of the products before using them.
Material Safety Data Sheet Stainless Steel SECTION 1:Identification of the Substance/mixture and of the Company/Undertaking GHS PRODUCT IDENTIFIER:STAINLESS STEEL OTHER MEANS OF IDENTIFICATION:Coil, Plate, Angle, Bar, Rebar and Wire Coil. RECOMMENDED USE OF THE CHEMICAL AND RESTRICTIONS OF USE:Solid stainless steel products, varies forms
Strength Of Steels - Roy MechThese standards relate to the delivery conditions for alloy and non-alloy steels supplied in cold rolled strips of up to 600mm width for heat treatment The steel names in these standards are allocated according to BS EN 10027-1 and CR 10260 and the steel numbers are allocated in accordance with BS EN
Technical Data Sheet - JotunCarbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1) - Environmental Product Declarations. Product-specific Type III EPD (ISO 14025;21930, EN 15804). LEED® (2009) - IEQ Credit 4.2:The VOC requirements of Green Seal Standard GC-03, 1997. The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet
protection of structural steel exposed to cellulosic fire. Can be used as mid coat or finish coat in atmospheric EN 13381-8 CE marked product with European Technical Assessment ETA-20/1295 Reaction to Fire:Class B-s1, d0 (EN 13501-1) The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS
Technical Data Sheet - atimetalsTechnical Data Sheet ATI 201LN ATI 201LN Stainless Steel:Austenitic (UNS S20153) INTRODUCTION. Materials for use at sub-zero temperatures should be ductile, tough and strong at their use temperature. Only a limited number of materials, among them most of the austenitic stainless steels, satisfy all of these requirements.
Technical Data Sheet - atimetalsTypical mechanical property data for ATI 500MIL-® specialty steel is included below. This data represents an average of results for 0.275 in. (7 mm) and 0.199 in. (5 mm) plate. HARDNESS . Steel will re-harden in the 477 to 534 BHN range. FLATNESS
Tubing Data 3 TUBING DATA Table 1Fractional Carbon Steel Tubing Allowable working pressures are calculated from an S value of 15 700 psi (108.2 MPa) for ASTM A179 tubing at 20 to 100°F (28 to 37°C), as listed in ASME B31.3. For working pressure in accordance with ASME B31.1, multiply by 0.85. Suggested Ordering InformationNORSOK STANDARDMaterial Data Sheets for Structural Steel M-120 Rev. 3, Dec. 2000 NORSOK Standard Page 4 of 4 Table 1:Material Data Sheets for Structural Steel MD S No. Rev. No. Standard Steel Grade Product Type Steel Qualit y Level Former designation EN 10025 S235JRG2 S275JR S355J0 Plates and Sections IV EN 10210 S235JRH S275J0H S355J0H Y01 3 Hot finished